![]() ![]() Avoid Under or Overpowering Lights with an Incorrect Power Source If your RGB tape lights won't change colors, try flipping your tape light around and reconnecting it. RGB or color-changing LED tape lights are particularly susceptible to this reversed polarity problem. The arrow on your connectors should point to the plus sign on your tape lights. Typically one side of the tape light carries a positive charge, noted by a single dashed line, and the other side has a negative charge, usually noted with the manufacturer logo. You could easily bend the pins or break them if you use too much force.Ī bad pin connection could also be caused by a backward connection or reversed polarity. These tiny connectors are rather delicate, so you have to be very careful when inserting them. Most likely, the pin is not inserted correctly. If your LED tape light fails to turn on at all, then check your pin connections. Solution: Check that the voltage of the lights and the driver match. Possible Cause: The power supply voltage is too high. Solution: Flip your tape light around and reconnect it. Possible Cause: The tape light is connected backward, reversing the polarity. This could be a significant safety concern. Hot and neutral wires should never touch. Solution: Check for correct wiring and polarity of power. Possible Cause: Crossed wires are causing the current to short. ![]() Solution: Split up your strip light run with multiple LED drivers, with a max of 16 feet per driver. Possible Cause: The strip has a weak electric current due to voltage drop. The light is a different color at the end of the strip. Solution: Disconnect the dimmer from the circuit, as dimmers prevent the tape light from flashing or chasing. Possible Cause: The lights are connected to a dimmer. Solution: Replace the controller batteries. Possible Cause: The batteries to your RGB controller are dying. ![]() Solution: Check that the voltage of the lights and driver match Possible Cause: The power supply voltage is too low. Ensure wire insulation is stripped at least half an inch on the ends and connections are sufficient. Possible Cause: A hardware issue, such as loose wires or too much wire insulation, preventing LED strips from receiving power. Possible Cause: For battery-operated lights, the batteries are dying. Solution: Confirm the tape light is plugged in and turned on. Possible Cause: The tape light isn't turned on or plugged into the wall. Solution: Check the connections and your dimmer's spec sheet to ensure compatibility. Possible Cause: The dimmer connection is loose or is not compatible with the LED tape light. How to Solve Seven of the Most Common LED Tape Light Issues: The following list outlines some of the most frequent causes of tape light failures and potential solutions, followed by more in-depth troubleshooting of two common tricky situations and more tips to have your LED light strips working properly in no time. However, even LED tape lights have their quirks and common issues. They are less daunting to budding DIYers and decorators than their rope light siblings due to their simple installation process often requiring no more than plugging them in to install. LED tape lights are the go-to lights for straight lines, right-angle corners, and subtle underlighting. If you spend a lot of time outdoors, try wrapping the lights around tree trunks and branches for added ambience to any outdoor space.Īs you can see, the possibilities for creating a beautiful look with rope lights are seemingly endless.Edited 6/26/23 by Harrison Hamilton & Hannah Lee Using rope lights to outline your pool or dock creates a stunning look with the benefits of functionality and safety. Rope lights can be used outdoors too! To make your yard stand out for an outdoor celebration, try edging your flower beds with rope lights to emphasize your gorgeous landscaping. You can also use the lights to spell out words and phrases on your walls-it just takes a little creativity and a few supplies, as seen in this tutorial! This look would be perfect for a child’s room or special occasion such as a wedding or engagement party.ĥ. This is a simple but elegant way to create some flair at home with lighting!Ĥ. Attach rope lights to the backs of headboards, TVs, and more to create a stunning backlit effect for a beautiful glow. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |